How to Fix Lonsdor K-prog2 Adapter Module is Not Bound

 Problem:

I need to read Volvo KVM data with Lonsdor K518ISE K-prog2 programmer. But it days run App failed. Adapter module is not bound. Any solution?

Solution:

You have to combine kprog2 adapter with K518ISE in order to read immo data.

Follow instruction here to bind kprog 2 with k518.

How to connect or bind KProg with Lonsdor K518:

If it’s the first time to use the KProg adapter, you need to bind it with K518ISE.

Connect kprog

Go to the K518ISE home page

Choose “Settings -> Bind adapter”

And follow the direction to finish binding

You have to know:

One K518ISE host can bind up to 5 adapters

And the bound adapter can not be bound to other K518ISE hosts.

Once bound, no need to bind again.

Lonsdor K518ISE Kprog2 Pinout

 Question: I am trying to read JLR all key lost 2018+ with Lonsdor K518ISE, this kprog2 adapter pinouts looks different from machine instructions, if there is any additional plus or cables need to purchase

see label don’t match the pinouts.

Solution:

Follow the wiring diagram in the instructions to connect. Don’t care about the text on kprog2 adapter.

then connect Dupont line to KPROG2, the other end to FS-01 board.

http://www.lonsdor.org/lonsdor-k518-kprog2-power-wire-connection-pinout/

Lonsdor K518ISE K518S EEPROM Chip List

Lonsdor K518ISE/K518S key programmer connecting the Kprog2 is able to read and write an eeprom soic chip/mcu chip.  You can get data for backup or replacement.

Lonsdor KPROG-2 Adapter Read & Write EEPROM Chip List

24 series   Support ATMEL & ST chip

AT24C01  128 byte

AT24C02  256 byte

AT24C04  512 byte

AT24C08  1K

AT24C16  2K

AT24C32  4K

AT24C64  8K

AT24C128 16K

AT24C256 32K

93 series; Support ATMEL & ST chip

AT93C46-8bit  128 byte  read/write

AT93C56-8bit  256 byte read/write

AT93C57-8bit  256 byte read/write

AT93C66-8bit  512 byte read/write

AT93C76-8bit  1024 byte read/write

AT93C86-8bit  2048 byte read/write

AT93C46-16bit   128 byte read/write

AT93C56-16bit   256 byte read/write

AT93C57-16bit   256 byte read/write

AT93C66-16bit   512 byte read/write

AT93C76-16bit   1024 byte read/write

AT93C86-16bit   2048 byte read/write

25 series; Support ATMEL chip

AT25010   128 byte

AT25020   256 byte

AT25040   512 byte

AT25080   1K

AT25160   2K

AT25320   4K

AT25640   8K

AT25128   16K

AT25256   32K

AT25M01   1M

AT25M02   2M

95 series; Support ST chip

95010   128 byte

95020   256 byte

95040   512 byte

95080   1K

95160   2K

95320   4K

95640   8K

95128   16K

95256   32K

95M01   1M

95M02   2M

Demo example:

flash an eeprom soic chip, read & write 93C66, confirm it’s working. reading the bin file

Solder chip to Kprog-2 adapter

Choose Adapter function->EEPROM->Common->93CXXX->Read data->select chip type

AT93C56-8 bit 256 byte

Save file name

Read eeprom success

Go to Hex Editor, open bin file you saved

Modify bin file and save

Go back to select “Write data” and choose proper eeprom type

Write eeprom finished.

Done.

http://blog.obdii365.com/2019/09/21/lonsdor-k518-kprog-2-eeprom-mcu-chip-list/

Lonsdor K518 KPROG2 Pinout to VOLVO XC90 CEM RENESAS M32C

Q: I want to read the Volvo XC90 CEM RENESAS M32C, but i cannot find the pin out of the Lonsdor K518ISEKPROG2. Can you send me the photos of the connection of the Kprog-2 adapter? This is the only one i found on official website.

Obdii365.com engineer solution:

You need to read CEM master data, 93c86 data and rearview mirror data for xc90.
use another programmer (i.e xprog) to read 93c86 data and rearview mirror data. use kprog 2 to read master data.

picture below shows how to wire.

(Click to enlarge)
instructions for picture 1:
note: cut off the power when wiring.
use needle 1 of the adapter to connect gnd
use needle 2 of the adapter to connect vcc
use needle 9 of the adapter to connect rxd
use needle 10 of the adapter to connect reset
use needle 11 of the adapter to connect txd
use needle 13 of the adapter to connect sclk
use needle 14 of the adapter to connect cnvss
use needle 15 of the adapter to connect busy
remove this chip when reading data. cut off the power supply and wire the chip back after reading data.

how to read master data with Kprog-2:
Lonsdor K518 → adapter → mcu → renesas → r32c/m16c/spi → read flash → read dataflash

position of 93c86

http://www.obdii365.com/producttags/lonsdor-k518ise.html

http://www.lonsdor.org/volvo-xc90-cem-renesas-m32c-pinout-to-lonsdor-k518-kprog2/

Lonsdor K518ISE KPROG-2 Adapter Kernel Update Guide

The tutorial: How to update KPROG-2 adapter kernel

After the APK of Lonsdor K518ISE device is updated to version 1.6.0 , the adaptor requires to be installed new kernel beforehand. Please refer to the following tutorial.

What’s a KPROG-2 adapter?

Source: http://www.obdii365.com/wholesale/kprog-adapter-for-lonsdor-k518ise-key-programmer.html

It’s an adapter used with Lonsdor K518ise for backup or replacement.

How to update KPROG-2 adapter kernel?

Step 1: Connect the device to the specified adaptor and plug in 12V power, as shown

below.

Step 2 : Start up the device, and input password to enter home screen. Click “Update

firmware” button in below red box.

Step 3: The following interface appears, click “Install Adaptor” in below red box.

Step 4: It skips to the below interface, click “OK” to continue.

Step 5: It skips to below interface. You will see the progress indicator moving

rightwards. When downloading is completed, click OK” and exit. The adaptor kernel

is installed successfully.

Job’s done!

Tech support from http://www.obdii365.com/

http://blog.obdii365.com/2018/05/31/lonsdor-k518ise-kprog-2-adapter-kernel-update-tutorial/