Problem: I had a problem with Lonsdor K518ISE and P0020B smart key pcb. It failed to obtain key data. Seems it is not a collectable type. Any solution?
Solution:
P0020B smart key pcb can only be used to transfer but no collect key data.
To collect key data you need H0440C, H0410C or PH0440B smart keys.
TOYOTA CAMRY 2019 – ALL Smart key lost programming with Lonsdor K518.
What’s required:
Lonsdor K518ISE
ADP adapter
LKE emulator
Connect ADP adapter with vehicle immo box and K518 device follow the wiring diagram
Step 1: Backup immo data
Select Backup immo data
Save Immo data
Step 2: Generate LKE
Select Generate LKE function
The function requires network connection
Put LKE emulator into K518 induction coil
Upload immo data read in step 1
Generate LKE emulator successfully
Step 3: Add smart key
Select Add smart key
Put emulator key into the induction coil
Put new key into k518
Program new key successfully.
Question: Will Lonsdor K518ISE write key to a 2020 Land rover Evoque?
2020 Evoque Low Configuration:
Lonsdor support OBD duplicates a new key. If some models ask for a 32-digit pin, it cannot be duplicated.
Supports all keys lost programming.
2020 Evoque High Configuration:
Add key: OBD duplicates a new key will not have keylessgo function, only remote and emergency start. To enable keyless function, you should perform all keys lost procedure.
JPLA version must replace CPU or RFA module, then do AKL under RFA replacement menu. Only in this case, the key will have keyless, remote, keyless entry functions.
If still no keyless function, you have to turn off the UWB function (two keys are required to replace the RFA module if you lose all keys).
To change the vehicle configuration, use the K518. To replace the RFA box or chip, use the 518 to operate first. Replace it, and then use 518 to program the key. (JLR adapter cable is required in the case of active alarms). If the K8D2 version, K518 cannot do it, it needs to be done by JLR official equipment.
LONSDOR JLR Jaguar Land rover 2018-2021 Key with Shell 5 Buttons
Lonsdor K518ISE program Volvo xc60 2009 all keys lost successfully. 2 key programmed. Failed to Yanhua MINI ACDP. Lonsdor did it.
How to know whether your Lonsdor K518ISE/K518S key programmer device get update package or not?(or check the update expiration time)
Lonsdor released Hyundai and Kia 8A smart key programming using PS6000B and PA7800B smart keys.
Here is the Hyundai Kia 8A smart keys supported vehicle list and shell.
Software and Frequency are convertible.
Supports P4 versions:
0000A3A3 / 000000D3 / 0000D3D3
0000B3B3 / 00002323 / 0000CECE
0000D0D0 / 0000D2D2 / 0000CDCD
Supported Models:
Chinese Hyundai/Kia
Sonata 9/15-17
Sonata 9 Hybrid/15-17
Beijing Hyundai 1X25/17-19
Kia K3/16-18
Beijing Hyundai IX25/-16 front
Beijing Hyundai 1X35/18+
Elantra leads 16-19
Global Hyundai/Kia
HYUNDAI Sonata 2015-2017
HYUNDAI Sonata Hybrid 2015-2017
HYUNDAI IX35 2018+
HYUNDAI Elantra 2016-2019
KIA K3 2016-2018
How to Program Hyundai Kia 8A Smart Key with Lonsdor K518?
Go to Special Functions-> Key Settings-> XD smart keys-> Smart key conversion
Convert PS6000B or PA7800B smart key to your original key version
Then go to the immobilizer menu, select corresponding models and program 8A smart key.
How-to: programming a 2007 Maserati Quattroporte via obd using londsor k518ise/k518s/k518usa key programmer. Went smooth pulled all data needed total time was 10 min job. Autel couldn’t do it. Londsor did it in 10 mins.
Steps are as follows. back up immo data first then make dealer key. Program key then program remote.
Here comes the problem:
I am using Lonsdor K518ISE to add a new key to a 2008 BMW CAS3++ ISTAP. Had battery stabilizer on 13.7 entire time and good internet.
Original key and new key not starting car.
New key buttons are working.
Error on dash car in hoist service error.
I’ve attached photos of the process.
Steps taken:
CAS 3
Update cas successfully
Add key
Made dealer key followed prompts
Not proxy so added remote key.
Used card slot to generate.
Everything seemed successful but car won’t start but buttons do work.
I’ve tried to synch ELV and DME.
No change
I did restore on cas
No change
Battery reset
No change.
Cleared fault codes
Solution:
cas3++ istap downgrade via OBD is very risky, better do it always on the bench.
Whenever you make a copy or all key lost, of these CAS3 or CAS3+ modules, the ideal is to do it on the bench, read the original file, no error. doing it by obd2 can corrupt CAS file.
You can use vvdi prog+vvdi2 or cgdi bmw on bench. Autel IM608 is way easier, faster and more guaranteed. the londsor is hit or miss on BMW.
http://blog.obdii365.com/2021/08/19/repair-bmw-cas3-istap-with-autel-im508-im608/
CAS and engine ECU lost ISN. You have to read ECU and CAS file to sync ISN.
You need good eprom and flash files to recover the cas then you need to to program key with Isn from DME
Then sync the cas with DME on the car.
Feedback:
Started again with Autel added a new key again and everything worked. Just connected the Autel downgraded again and added key once I cleared the ELV the error went and everything worked. Autel for the Win!
http://www.lonsdor.org/lonsdor-k518ise-bmw-cas3-istap-car-not-start/
Will Lonsdor K518ISE program Toyota 2022 smart keys, i.e Land cruiser 2022 add key and all keys lost? If yes, what key to use? original key, aftermarket key or must be Lonsdor key?
Here’s the clue:
Check the P04 page of the smart key, if P4 ends with BABA or 3939, Lonsdor cannot do all keys lost, only add key.
If P04 page is not BABA or 3939, Londsor will do both add key and all keys lost.
All keys lost requires ADP adapter and LKE emulator. Generate LKE emulator and add key. You can use either OEM, aftermarket or Lonsdor keys as well as key board is correct.
Example:
Program 2018-2022 Toyota Camry 8A All Keys Lost by Lonsdor ADP Adapter
Program Toyota RAV4 2021 All Keys Lost with Lonsdor K518 & ADP Adapter
Lonsdor K518ISE Adds Toyota Corolla 2021 4A Key with ADP Adapter
